McQuay MHW Geothermal Ran Manual de instalación descargar pdf (Pagina 4)

Page 4 of 38 / IM 985-2

Pre-Installation

WARNING

The installer must determine and follow all applicable

codes and regulations. This equipment presents hazards

of electricity, rotating parts, sharp edges, heat and weight.

Failure to read and follow these instructions can result in

property damage, severe personal injury or death. This

equipment must be installed by experienced, trained

personnel only.

1. To prevent damage, do not operate this equipment

for supplementary heating and cooling during the

construction period. Doing so will void the warranty.

2. Inspectthecartonforanyspecictaggingnumbers

indicatedbythefactoryperarequestfromtheinstalling

contractor. At this time the voltage, phase and capacity

shouldbecheckedagainsttheplans.

3. Checktheunitsizeagainsttheplanstoverifythattheunit

isbeinginstalledinthecorrectlocation.

4. Beforeinstallation,checktheavailabledimensionswhere

theunitbeinstalledversusthedimensionsoftheunit.

5. Note the location and routing of water piping, condensate

drain piping, and electrical wiring. The locations of these

itemsareclearlymarkedonsubmittaldrawings.

6. Theinstallingcontractorwillnditbenecialtoconfer

withpiping,sheetmetal,andelectricalforemenbefore

installing any unit.

Note: Check the unit data plate for correct

voltage with the plans before installing the

equipment. Also, make sure all electrical

ground connections are made in accordance

with local code.

7. The contractor shall cover the units to protect the

machinesduringnishingofthebuilding.Thisiscritical

whilesprayingreproongmaterialonbarjoists,

sandblasting,spraypaintingandplastering.Damageto

theunitduetoafailuretoprotectitduringnishingofthe

buildingisnotcoveredbythewarranty.

Receiving and Storage

Uponreceiptoftheequipment,checkcartonforvisible

damage.Makeanotationontheshipper’sdeliveryticket

beforesigning.Ifthereisanyevidenceofroughhandling,

immediatelyopenthecartonstocheckforconcealeddamage.

If any damage is found, notify the carrier within 48 hours to

establishyourclaimandrequesttheirinspectionandareport.

TheWarrantyClaimsDepartmentshouldthenbecontacted.

Do not stand or transport the machines on end. For storing,

eachcartonismarkedwith“up”arrows.

Intheeventthatelevatortransfermakesup-endedposition-

ingunavoidable,donotoperatethemachineuntilithasbeen

in the normal upright position for at least 24 hours.

Temporarystorageatthejobsitemustbeindoor,completely

sheltered from rain, snow, etc. High or low temperatures

naturally associated with weather patterns will not harm

the units. Excessively high temperatures, 140°F (60°C) and

higher, may deteriorate certain plastic materials and cause

permanent damage.

IMPORTANT

This product was carefully packed and thoroughly

inspected before leaving the factory. Responsibility for its

safe delivery was assumed by the carrier upon acceptance

of the shipment. Claims for loss or damage sustained in

transit must therefore be made upon the carrier as follows:

VISIBLE LOSS OR DAMAGE

Any external evidence of loss or damage must be noted

on the freight bill or carrier’s receipt, and signed by the

carrier’s agent. Failure to adequately describe such

external evidence of loss or damage may result in the

carrier’s refusal to honor a damage claim. The form

required to le such a claim will be supplied by the carrier.

CONCEALED LOSS OR DAMAGE

Concealed loss or damage means loss or damage which

does not become apparent until the product has been

unpacked. The contents may be damaged in transit due

to rough handling even though the carton may not show

external damages. When the damage is discovered upon

unpacking, make a written request for inspection by the

carrier’s agent within fteen (15) days of the delivery date

and le a claim with the carrier.

Table 1: Physical Data

Unit Size 007 009 012 015 018

Fan Wheel - D x W (In.)

4.33 x 27.24 4.33 x 27.24 4.33 x 27.24 4.33 x 35.43 4.33 x 35.43

Fan Motor Horsepower

1/30 1/30

1/30 1/18 1/18

Coil Face Area (Sq. Ft.)

1.67 1.67 1.67 2.22 2.22

Coil Rows

2 2 3 2 3

Refrigerant Charge (Oz.) 18.2 19.2 22 29.9 32

Filter, (Qty.) Size (In.)

Low Sill

(1) 23.75 x 8.75

(1) 31.75 x 8.75

High Sill

(1) 29.25 x 9.75 (1) 37.25 x 9.75

Water Connections, Female NPT (In.)

5/8 O.D. 5/8 O.D. 5/8 O.D. 5/8 O.D. 5/8 O.D.

Condensate Connections, Female NPT (In.)

3/4 I.D. 3/4 I.D. 3/4 I.D. 3/4 I.D. 3/4 I.D.

Weight, Operating (Lbs.)

138 144 146 166 171

Weight, Shipping (Lbs.) 158 164 166 196 201

1 2 3 4 5 6 7 8 9 ... 37 38

Comentarios a estos manuales

Sin comentarios

McQuay MHW Geothermal Ran Manual de instalación Pagina 4

Comentarios a estos manuales

Relacionado con productos y manuales para Termostatos McQuay MHW Geothermal Ran